Doors (External) 
Doors (Internal) 
Barns (External) 
Barns (Internal) 
Cabinets 
Decking 
Fences 
Floors 
Furniture 
Garden Furniture 
Garden Paints 
Guitars & Musical Instruments 
Log Cabins 
Sheds 
Sleepers 
Stairs 
Summer Houses 
Tables 
Toys (Wooden) 
Windows 
Woodturning 
Worktops Osmo LED Smart-Oil
Surface Preparation
The wood surface must be clean, dry, and frost-free (max. 12% wood moisture content).
Osmo LED Smart-Oil is ready to use; do not dilute. Stir thoroughly.
Old paint and varnish coatings must be completely removed.
Fill small cracks, larger gaps, or holes in the wood (with wood filler or joint compound). Carefully sand the wood surface, starting with coarse sandpaper – final sanding with colourless sandpaper for floors (P100-120), furniture (P120-180).
Before oiling, remove sanding dust from the surface by sweeping and vacuuming.
Method of Application
Apply the LED Smart-Oil thinly with a double-bladed spatula or similar tool.
For V-joints or other open surfaces, apply partially with a microfibre roller (not the entire surface). Then, spread the oil with a white pad manually or with a single-disc, massaging the product into the surface, and smooth the area without streaks. If streaks remain due to too much product, we recommend turning or replacing the pad.
Next, cure the surface finish with an UV LED spotlight at a distance of at least 2cm and no more than 10cm from the surface.
If a satin sheen is desired, apply the LED Smart-Oil again. To do this, lightly sand the first coat with fine P240-320 sandpaper, then apply the Smart-Oil very thinly (approx. 5-10 ml/m²) and smooth and cure as described above.
Note
LED Smart-Oil does not dry oxidatively. Without irradiation with suitable LED spotlights, or if LED spotlights with insufficient power or dose are used, complete curing will not occur and the surface will be unusable.
Caution: Add only a small amount of LED Smart-Oil to a paint tray or similar container to avoid a pre-reaction. When working with the liquid material, absolutely avoid direct sunlight and bright light with a UV component (e.g. from conventional LED lamps). If the surface is exposed to sunlight, curing will begin during application due to the UV rays! Cover/darken windows if necessary.
LED Smart-Oil enhances the natural color of the wood (permanent wet effect). For a nearly natural-looking surface, use LED Smart-Oil 5984 Natural (no permanent wet effect).
When using extractive hardwoods (e.g. wenge, merbau, jatoba, etc.), a test application is recommended.
Can be dried with suitable LED handheld systems. For coloured LED Smart-Oils, apply the first coat in the coloured version and the second coat in the colourless version (except for 5981 White). A coloured primer can also be applied using Osmo Oil Stain. Apply the oil stain according to the product information and allow it to dry for approximately 48 hours before applying the colourless LED Smart-Oil.
Safety instructions for UV radiation devices
During operation, intense UV light is emitted. UV light can damage eyes and skin. Do not look directly into the switched-on lamp (risk of blindness). Reflected UV light can be just as dangerous as direct light. Skin burns from UV radiation. Observe the manufacturer’s operating instructions during operation. Always wear approved UV protective goggles or a UV protective shield (EN166:2002). Wear clothing that covers the skin. Use additional suitable skin protection (sunscreen). Never point the switched-on lamp at people or animals.
Safety Instructions
Causes serious eye irritation. May cause allergic skin reactions. Harmful to aquatic life with long-lasting effects. Avoid release into the environment. Wear protective gloves/eye protection.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
IF ON SKIN: Wash with plenty of water. In case of skin irritation or rash: Seek medical advice/attention.
Contains: Glycerol, propoxylated, ester with acrylic acid (< 6.5 mol PO); propylidynetrimethanol, ethoxylated, ester with acrylic acid, reaction products with diethylamine; Trimethylolpropane, ethoxylated, esterified with acrylic acid; Ethylphenyl(2,4,6-trimethylbenzoyl)phosphinate; EU limit value for the product(Cat. Ai): 500 g/l VOC.
This product contains max. 10 g/l VOC.
Care
Regular Cleaning: Dust mopping. Damp mopping using Osmo Spray-Cleaner.
Recoating: Simply re-apply one coat of LED Smart-Oil onto the clean and dry surface when signs of wear become visible.
Finishes
1 clear wood finish and 11 colour wood finishes.
First coat is a matt finish. Second thin coat will be a satin finish.
Application Tools
Apply with Osmo Double Blade Scraper tool or microfibre roller. Then, spread the oil with a white pad and massage it into the surface, streak-free.
Recommended Use
Wooden flooring, staircases, furniture, etc.
Recoat
One coat, when signs of wear become visible
Sizes
750ml, 2.5L
Dry Time
Instantly with Osmo UV LED Smartlight Pro (Sold Separately)
Clean Up
Osmo Brush Cleaner
Coverage
40-50m²/L with one coat
Coats
One coat for a matt finish. Two coats for a satin finish.
Care
Osmo Spray Cleaner
No posts found
Osmo LED Smart-Oil
